الخطوات بالصورSteps in pictures

- 1تثبيت الحامل الخارجي بالميزانOutdoor unit steel bracket fixed on an exterior wall and checked with a level
- 2اللوح الخلفي للوحدة الداخلية وفتحة بميل للخارجIndoor unit mounting plate fixed with a level and a wall hole drilled sloping slightly outward
- 3فلير المواسير وربطها بمفتاح العزمCopper pipes flared and tightened with a torque wrench, insulated
- 4تفريغ الهواء بمضخة التفريغ ثم فحص الصرفA vacuum pump with gauge manifold connected to the service valves, then the drain hose check
وحدة داخلية وأخرى خارجية يربطهما أنبوبا فريون (سائل وغاز) وكابل تحكم وخرطوم تصريف مياه.
An indoor and an outdoor unit linked by two refrigerant pipes (liquid and gas), a control cable and a condensate drain hose.
قبل البدءBefore starting
نقطة إيقافHold pointاعتماد أماكن الوحدات مع العميل (مسار الهواء وبعدها عن السرير ومقاعد الجلوس)؛ اعتماد مسار المواسير والتصريف قبل المحارة والجبس؛ حمل الحامل الخارجي وقدرته على تحمل وزن الوحدة؛ مأخذ كهربائي مخصص بقاطع مناسب.
Approve unit positions with the client (airflow and distance from beds and seating); approve the pipe and drain route before plastering and gypsum work; check the outdoor bracket and that it can carry the unit's weight; a dedicated power point with a suitable breaker.
الخطواتSteps
- تثبيت الحامل الخارجي وفق مستوى وميل صحيح
- تثبيت اللوح الخلفي للوحدة الداخلية بمستوى ميزان
- عمل فتحة المرور في الحائط بميل خفيف للخارج لتصريف المياه
- تمرير المواسير المعزولة وكابل التحكم
- وصل المواسير بالوحدتين بأدوات وصل مناسبة
- تفريغ الهواء من الدائرة بمضخة تفريغ (Vacuum) قبل فتح الفريون
- فتح الفريون والتشغيل وقياس التبريد
- عزل الوصلات وتغطية المواسير الظاهرة بغطاء
- Fix the outdoor bracket level and at the right angle
- Fix the indoor unit's back plate level
- Core the wall opening with a slight fall to the outside for drainage
- Pass the insulated pipes and control cable through
- Connect the pipes to both units with proper fittings
- Evacuate the circuit with a vacuum pump before releasing the refrigerant
- Open the refrigerant, run the unit and measure the cooling
- Insulate the joints and cover exposed pipes with trunking
خلّي بالكWatch out
عدم ثني المواسير النحاسية بزاوية حادة؛ عزل المواسير بالكامل لمنع التكثف؛ ميل خرطوم التصريف باتجاه الخارج وعدم تعليقه؛ حماية الوحدة الخارجية من أشعة الشمس المباشرة إن أمكن.
Do not bend copper pipes sharply; insulate the pipes fully to stop condensation; give the drain hose a fall to the outside and do not let it sag; shade the outdoor unit from direct sun if possible.
الأجهزة القائمة تُفك وتُعاد (بند فك وإعادة تركيب) وغالباً تحتاج مواسير جديدة أو غسيل؛ تأكد من حالة المواسير القديمة قبل إعادة استخدامها.
Existing units are removed and refitted (a separate remove-and-refit item) and usually need new pipes or flushing; check the condition of old pipes before reusing them.
الاستلامAcceptance
نقطة قبولAcceptance pointلا تسريب ولا ضوضاء مبالغ فيها؛ تصريف المياه يعمل؛ عزل المواسير سليم؛ ثبات الوحدة الخارجية؛ تسليم الريموت وكتيب الاستخدام والكفالة.
No leaks and no excessive noise; condensate drains; pipe insulation intact; outdoor unit firm; remote, user manual and warranty handed over.
عيوب شائعةCommon defects
تنقيط من الوحدة الداخلية (ميل التصريف أو العزل)، ضعف تبريد (فريون ناقص أو تسريب)، صوت اهتزاز (حامل غير ثابت).
Dripping from the indoor unit (drain fall or insulation), weak cooling (low refrigerant or a leak), vibration noise (loose bracket).
عايز بنية تنفّذ؟Want Bunyh to do it?فريق Bunyh Contracting بينفّذ بنفس الخطوات ونقاط الفحص دي.Bunyh Contracting executes with these same steps and checks.
اطلب معاينةRequest a site visitعايز مهني موثّق ينفّذ؟Need a verified professional?تطبيق بنية بيوصّلك بمهنيين موثّقين وعروض أسعار تقدر تقارنها.The Bunyh app connects you with verified professionals and quotes you can compare.
سجّل اهتمامكJoin the waitlist
